Instruments
Universal Material Tensile Machine

Introduction: BGD 570/571 Universal Material Tensile Machine is a new type of material machine which combines the electronic technology and mechanical transmission. It has wide accuracy acceleration and test force range, not only measuring and controlling the load and displacement in higher accuracy and sensitively, but also doing the control test by automatically of isokinetic load and displacement. It operates easily and conveniently, especially applied in inspect instruments which is used for controlling products of produce line. This series of tensile machine is mainly suit for non-metal and metal test with test load less than 20KN (BGD 570) or 50KN (BGD 571). 

The electronic universal material tensile machine is mainly suitable for testing metal and non-metal materials, such as rubber, plastic, wire and cable, optical fiber cable, seat belt, safety belt, leather belt composite material, PVC, waterproof coiled material, steel pipe, copper material, section bar, spring steel, bearing steel, stainless steel (and other high hardness steels), castings, steel plates, steel belts and non-ferrous metal wires. To test their functions which include stretching, compression, bending, shearing, stripping, tearing, two-point extension (additional extension meter is required) etc.


Character
StandardsISO 527, ISO 604, ISO 178, ISO 1209, ASTM D 638, ASTM D 903
High precision sensoruse high precision ball screw as driving mechanism
Frequency of collecting data200 times/second
Can store many testing results of referenced points, calculate average value automatically, grab automatically max. value, force value at break.
Set range of break point proportion099% and can set freely according to different samples, accomplish stopped status at different position.
Safety DeviceOver loading, Emergency shut down, limitation device for above travel and under travel.
Collect date synchronously, conversable full 24 bits AD codes,, resolution arrives 1/500,000, surpass all competitors.
More than one thousand clamps and grippers for selection.
Support multi-sensors, can equip with a few sensors at the same time for different range.
 
User can calculate elastic modulus, yield point, constant residual strength, constant elongation, constant force deformation and maximum strength. There are other special professional calculations, such as the calculation of belt stripping and the elongation at yield point.

 Optional measure and control system of professional test machine, which can realize the closed loop of force value, deformation and position, so that the tensile machine can carry out curve control tests freely, such as low frequency cycle (fatigue) test, step test and force value holding (creep) test.


Measure and Control System 

Function 

Standard open-loop 

control system

(standard configuration)

 Standard open-loop control system

(optional)

Position (displacement speed)

Forceforce value speed

×

Deformation

×

Multiple control (position, force, 

    deformation control exchange)

×

Cycle control

×


Measure and Control System Introduction
 
      We use newest system which was developed in 2008. With strong functions and convenient application such as language conversion, translate automatically testing results, units conversion, manage sample shape, manage users, process data, generate report etc.,  This system uses newest tools --Visual Studio .Net 2005 which is developed by Microsoft . With strong function and friendly windows, it become a developing tool for new generation operation system, and arrive more than 90% areas and population of global.

BGD 570-02.jpg

The Characteristics of Software:

◆ Operating interface attached with graph, image: intuitive and convenient to use, and it will decrease the operation error by voice mentioned, improving the reliability at the same time.

◆ MS-ACCESS database technology and SQL technology: it is not only applied for data preservation and processing standardization, but also convenient for connecting to Intranet or Internet. It can also connect Word or Excel etc software easily. User can read original test data just through standard database.

◆ Modular programming: VBScript can enlarge the user's reporter and parameter program by automatic calculation. User can develop by secondary, it can realize stretching, compression, bending, tearing, stripping, shearing etc test functions except for software bag.

◆ The curve graph function: through modular programming, real-time curve graphs will be displayed during the test, and parameter types can be selected for the coordinate axis of curve graphs. In theory, there are 169 kinds of graphs, from which parameters can be displayed.

◆ Multi-sensor support: it can support 5 force value sensors, 5 deformation sensors + large deformation + displacement, which expanded the test range greatly. 


NOTE: The minimum requirements of PC: Windows 7/Windows 8/Windows 10 operating system, USB2.0/ USB3.0 interface, CPU 3.0 GHz, 4 GB of memory, 100 GB of hard disk, wide screen color display (the minimum resolution: 1366*768).

 



◆ Three-way independent simulant input channel, 24 bits AD converter, gain amplifier controlled by program.

◆ Use USB 2.0 insulated photoelectricity to connect computer, reduce disturb and increase reliability.

◆ Unit for testing force uses the newest high-speed, high resolution, high precision, no dividual grade AD converter which can arrive ±500,000 fractionized codes. Its superior to six grades amplifier and reach or approach advanced international standards.

◆ Unit for testing big distortion:this system use high-speed circuit system to accomplish four-quadrant collection of photoelectric encoder, solve all influence to testing results because of dithering under low speed and redirection thoroughly, and increase four times resolution to big distortion of test machine big distortion.

◆ Unit for testing displacement:use high-speed circuit system to accomplish four-quadrant collection of photoelectric encoder, solve all influence to testing results because of dithering under low speed and redirection thoroughly, and increase four times resolution to big distortion of test machine big distortion.

◆ Unit for controlling speed:full digital controlling unit and its speed regulation ratio arrive 1:500,000, namely 0.001 ~ 500mm/min(precision : 0.1%), and can be tested under the whole range.

 

 

Main Technical Parameters

Product →

Parameters↓

BGD 570

Universal Material Tensile Machine

BGD 571

Universal Material Tensile Machine

Max. range (optional)

100N, 200N, 500N, 1KN, 2KN, 5KN, 10KN, (can be extended to 20KN)

50N, 500N, 5KN, 10KN, 20KN, 50KN

Precision grade

Grade 1

Measuring range of

test force

1%~100 FS (full range)

Display error of 

test force

Within ±1% (indicating value) /

Within ±0.5% (indicating value) 

Resolution of 

test force

±1/500000 of max. force (There is no grade in the whole process, and keep the constant

 resolution throughout the whole process.) 

Load sensor

Standard configured one tension and pressure sensor (maximum load);

Up to 5 sensors can be added.

Valid test width

380mm

450mm (can be widened as required) 

Valid tensile space (no including clamp)

1100mm (can be lengthen as required)

1000mm (can be lengthen as required) 

Test speed

0.001500 mm/min

0.001400 mm/min

Display error of 

displacement

Within ±0.5% (Indicating Value) /

Within ±0.2% (Indicating Value) 

Control system of

deformation (optional)

A. Large deformation measure system: the minimum gauge distance is 10mm, the 

deformation range is 800mm. 

B. Small deformation measure system: gauge distance: 25mm, 50mm, 100mm

deformation range: 5mm, 10mm, 25mm  

Control accuracy of 

deformation speed

Within ±0.5% of indicating value (large deformation or small deformation can be selected

 by customers) 

Safety device

Electronic limit protection

Lifting device of 

     working platform

Fast/slow speed automatic control, can move by yourself 

Return function

Manual or automatic.

After the test is completed, it returns to the initial position at the highest speed. 

Overload protection

If the maximum load exceeds 10%, the machine will be automatically stopped.

Clamp

A set of clamp (special clamps can also be designed according to the customers' sample 

 specifications.

Overall size

700mm x 530mm x 2200mm (L x W x D)

880mm x 530mm x 1800mm (L x W x D)

Power system

Servo machine + ZNT high accuracy ball screw

Servo machine + transmission + high 

         accuracy ball screw

Power supply

220V, 50HZ

Power

0.4 KW

1.0 KW

Weight

300 KG

380 KG

 
 

 

Optional Accessories

BGD 570/K---Low temperature tensile test chamber

BGD 1530---Bond strength pulling head (40mm×40mm)

BGD 1531---Bond strength pulling head (50mm×50mm)

BGD 1550---Large deformation device for double column tensile machine (only applicable to door/double column tensile machine, see NOTE)

BGD 1551---Small range sensor of tensile machine (<500KG)

BGD 1552---Large range sensor of tensile machine (>500KG)

BGD 1553---Pneumatic cutting machine

BGD 1554---Dumbbell type sample strip cutter

BGD 1555---Right-angle tearing sample strip cutter

BGD 1700---Plane clamp

BGD 1701---Eccentric wheel clamp

BGD 1702---Wedge clamp for metal

BGD 1703---Wedge clamp for hard plastic


NOTE: About the elongation of test materials

The displacement measure system, which is contained in tensile machine, only measures the moving distance of the crossbeam. If you need to measure the elongation of materials, such as elastic coatings or rubber products, additional large deformation device is required.


Subject:
Company:*
Name:
E-mail:*
Country:*
Comments:
Verification Code:Click ChangeCan't see clearly. Change it?
 
Send message
Contact USMore

Biuged Precise Instruments (Guangzhou) Co.,Ltd

AddNO.15, Fuzhong Rd., Zhongxin Town, 

Zengcheng District, Guangzhou.China

Tel+86-20-32955819 

Fax+86-20-32955820 

E-mailsara @ biuged.com

Website http//www.biuged.com 


Biuged Laboratory Instruments (Guangzhou) Co.,Ltd.

Add:RM.101, NO.3, Sicheng Rd.,
Gaotang Software Park, Tianhe District,
Guangzhou.China

Tel:+86-20-32955999

Fax:+86-20-32955818

E-mail:sara@biuged.com





Biuged Precise Instruments (Shanghai) Co.,Ltd

Add:No.1111, ZhongCai Industrial Park
1st floor,Zhu Feng Road, Qingpu District
Shanghai City, China.

Tel:+86-21-59240298

Fax:+86-21-59249719

E-mail:xjx@biuged.com

??Biuged Laboratory Instruments (Guangzhou) Co., Ltd. ??Guangdong ICP record number:11044672

XML 地图 | Sitemap 地图